Cutting Disc MOVA VIAX 250, 300 & 500

Replacement cutting disc · MOVA VIAX 250, 300 & 500

Whether the lawn in front of the house looks like a well-kept carpet or looks tired depends on the mowing disc of your VIAX. Here you will find the right replacement cutting disc for MOVA VIAX 250, 300 and 500 – optionally with 6, 7 or 9 blades, each version with protective frame and pre-assembled blades.

✓

Fits VIAX 250, 300 & 500

One disc for all three MOVA models

✓

6, 7 or 9 blades

You decide how finely the lawn looks

✓

Protection on every Mähteller

Less grass clumping, quieter operation

✓

Green instead of brown tips

Sharp blades cut instead of tearing

✓

Blades pre-assembled

Attach and keep mowing

✓

60 blades set optional

Fresh cut until the end of the season

6, 7 or 9 blades – how well-groomed should your lawn look?

All three versions fit identically on VIAX 250, VIAX 300 and VIAX 500 and are each supplied with a protective frame. The difference lies in the cut pattern: the more blades work on the mowing disc, the finer each blade of grass is trimmed – and the more well-groomed the area looks when viewed from the terrace.

6 blades

The reliable everyday cut

The classic replacement for the worn disc: six sharp blades restore the cut your VIAX was delivered with at the beginning. The right choice when you want the lawn to look neat and even again.

7 blades

A visibly denser lawn pattern

With seven blades, every blade of grass is captured more often and cut cleanly. The result is especially noticeable on areas you see every day: the lawn looks denser and more even, without your VIAX needing to drive differently.

9 blades

Sunday look – every day

Nine blades shorten the grass at particularly short intervals – the finest cut pattern in this series. For everyone who sees the lawn as the calling card of the garden and doesn’t want to discover frayed tips even up close.

+

Any number of blades, even in the set with 60 replacement blades

A lawn that should look good every day needs blades that are sharp every day. With the 60 blades set, you replace dull cutting disc blades immediately, instead of waiting for the next order – and you pay less in the set than when buying individually.

Ready-to-install cutting disc with mounted blades for MOVA VIAX 250, 300 and 500 — Delivered fully equipped – the blades are already mounted

Why the lawn can look dull despite mowing every day

Your VIAX reliably makes its rounds, and yet the lawn loses its shine: the area looks lackluster, the rich green gives way to a grayish haze. The cause is almost always underneath the robotic lawnmower – worn blades tear the blades of grass instead of cutting them cleanly.

Torn blades of grass dry out at the cut point and turn brown. Up close, it’s only a few millimeters; from a few meters away, thousands of such tips add up to exactly the tired impression you notice when you’re having coffee on the terrace.

A fresh cutting disc for MOVA VIAX 250, 300 and 500 turns the cut pattern around: smooth cutting edges that stay green, an evenly dense lawn carpet, and a robotic lawnmower that no longer has to work against resistance from dull blades – which also protects the motor.

The disc arrives fully equipped: all blades are already mounted, there’s nothing to screw on and nothing to prepare – unpack, attach, and the next round of your VIAX already shows the difference.

The protective frame keeps the mowing disc free – and your evening calm

No matter whether you choose 6, 7 or 9 blades: every version of this cutting disc includes a protective frame that keeps the blades securely in position and keeps the grass flow through the mowing disc open. Damp clippings that would otherwise wrap around the blades and slow down rotation get significantly less surface area to cling to.

You’ll notice it less on the robotic lawnmower than in the evening on the terrace: no clumps of grass left behind in the area, no half-cut spots where the VIAX has gotten stuck – just a lawn that looks finished when you come home.

Maintenance is also a secondary matter: remove the old cutting disc, attach the new one – the swap is done in just a few minutes and, as a rule, requires no tools. After contact with branches, stones, or roots, it’s worth taking a quick look at the mowing disc before the next round starts.

Before winter, it’s enough to free the cutting disc from grass residue and moisture – this way, your MOVA starts in spring right away with a clean first cut into the new season.

Mowing disc with protective frame for MOVA VIAX robotic lawnmower – 6, 7 and 9 blade variants — Mowing disc with protective frame – included with all three blade counts

Simply select the blade count above that matches your needs – 6, 7, or 9, optionally right away as a 60 blades set with replacement blades. Each variant fits MOVA VIAX 250, 300, and 500 and is delivered ready to install with protective frame and mounted blades.

Detailed product description & technical detailsshow ▾

Cutting disc for MOVA VIAX 250, 300 and 500 – mowing disc with protection and 6, 7 or 9 blades

A cutting disc for MOVA VIAX 250, 300 and 500 is the component that determines the look of your lawn anew every day: it carries the rotating blades, guides them during operation, and thereby determines whether the area in front of the house looks freshly cut after each ride or only „worn down“. On this page, you choose the right replacement mowing disc in three versions – with 6, 7 or 9 blades, each with protection and fully equipped.

A replacement part for three VIAX models

The cutting disc is intended for the compatible MOVA models VIAX 250, VIAX 300, and VIAX 500 – all three use the same disc mount, so you don’t have to look for a separate replacement part for each model. Please compare the model name of your robotic lawnmower and the design of the existing cutting disc before ordering, so that the mount and fastening fit together securely.

The number of blades determines how the lawn looks

With the 6-blade version, you replace the worn disc and restore a proper, even cut. The 7-blade version captures every blade more often and makes the area appear visibly denser. The 9-blade version delivers the finest result in the series: the grass is trimmed at particularly short intervals, the tips stay smooth, and the lawn maintains a well-groomed look even up close. Mechanically, all three variants fit identically on the VIAX.

Protection for the disc – for every blade count

Each version of this cutting disc is supplied with protection. It supports controlled blade guidance and keeps grass flow on the mowing disc clear: damp grass clippings that would otherwise collect around the blades and slow down rotation become a problem far less often. That means fewer blockages, fewer areas left behind in the lawn, and a VIAX that mows its area without interruptions.

Pre-assembled blades – delivered ready to install

The blades are already securely mounted on the disc upon delivery – six for the 6er variant, seven for the 7er variant, and nine for the 9er variant. You don’t have to assemble anything or adjust anything: the disc is taken out of the packaging, attached, and the robotic lawnmower can start its next round right away with fresh cut pattern.

Swap in just a few minutes

The replacement of the cutting disc on the MOVA VIAX is intentionally kept straightforward: switch off the robot, carefully tilt it, remove the old disc, fit the new one – usually without any tools. Gloves are still recommended, because even dull blades still have sharp edges. This keeps maintenance a matter of minutes and the lawn stays in shape without a long pause.

How you can tell when the disc is due

The lawn itself shows it first: brown discoloration, frayed blade tips, a dull overall impression despite regular mowing, or grass that seems more crushed than cut. Even if the blades no longer sit firmly, the mowing disc shows visible signs of wear, or the robot runs unevenly, replacement is a good idea. After contact with branches, stones, or roots, the mowing disc should also be checked – a bent disc worsens blade guidance and unnecessarily puts strain on the motor.

Optional as a set with 60 replacement blades

Each blade count is optionally available in a set with 60 replacement blades. If you maintain your lawn as a showcase for your garden, you replace dull blades immediately rather than later – with the supply in the cupboard, it’s a matter of moments, and in the set the replenishment costs less than buying later as individual items.

Compatible replacement part from CUT GUARD

This cutting disc is a compatible replacement part from CUT GUARD and not an original MOVA part. It is precisely made for the disc holder of VIAX 250, 300 and 500 and is designed for regular use in the robotic lawnmower. Please compare the model number of your device before purchasing to ensure the correct fit.

Benefits at a glance

Cutting disc for MOVA VIAX 250, 300 and 500 robotic lawnmowers – one holder for all three models
Three versions: 6 blades (everyday cut), 7 blades (denser lawn pattern), 9 blades (finest cut)
Protection with every version – free grass flow-through, fewer blockages on the mowing disc
Blades pre-assembled – swap in a few minutes, usually without tools
Optional as a set with 60 replacement blades – more cost-effective than buying individually
Usable as a blade plate, mowing disc or cutting disc for maintenance and repair

Whether you’re looking for this component as a Mowing disc for MOVA VIAX 250, a Blade plate for the VIAX 300, or a Cutting disc for the VIAX 500 – order here a ready-to-install replacement part that makes the view from the terrace enjoyable again: deep green, evenly dense, and freshly cut every day.

More MOVA models

4.0 out of 5

2 Reviews

5 stars 50%

4 stars 0%

3 stars 50%

2 stars 0%

1 stars 0%

Top reviews

B Björn 🇸🇪

Verified purchase

23. July 2026

I bought a new cutting disc for my MOVA VIAX 300 after the grass started to clump a bit in tougher areas, and it actually seems to help. With the six blades and the guard, everything runs more evenly with fewer stops, even in my slightly larger yard shed area of around 600 m². The swap itself was smooth and the fit is good. However, it arrived in a rather thin cardboard box, so the packaging felt a bit on the light side when you get it home in mailbox mode.

C Christian 🇩🇰

Verified purchase

8. July 2026

I bought the cutting disc for my MOVA VIAX 300. After the grass started sticking to the cutting equipment in the slightly thicker areas, I tried two other brands and ended up here—the included protection and the six blades made a clear difference: fewer grass blockages and a smoother run. It also fit without any problems, and I could mount it quickly without adjusting anything. Christian

Write a review

CUT GUARD Assembly Instructions

General assembly instructions for cutting discs, replacement blades, and blades for compatible robotic mowers.

Note

These instructions generally apply to compatible cutting discs, replacement blades, and blades from CUT GUARD.
They do not refer to a specific model or version. Always additionally refer to the operating manual of your robotic mower.

Important Safety Notice

Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Always wear appropriate protective gloves during assembly, disassembly, cleaning, and maintenance.
Never work on the cutting disc while it is still moving.

1. General Safety Instructions

The operator is responsible for accidents, injuries, and damages caused to other persons or their property.
Keep children, animals, and uninvolved persons away during work and operation of the robotic mower.
Never touch the cutting disc or the knives while they are still moving.
Always turn off the robotic mower completely before performing work on the cutting disc or the knives.
Remove the battery if possible or disconnect the device from the power supply.
Always wear appropriate protective gloves.
Do not use damaged, bent, heavily worn, or corroded knives, screws, or cutting discs.
Regularly check the condition of the knives, fastening screws, and the cutting disc.

2. Required Tools and Materials

Suitable screwdriver or bit, matching the screws used.
Protective gloves.
New or tested fastening screws.
CUT GUARD cutting disc, replacement blades, or blades.
Optional: soft surface for safely placing the robotic mower.

Important

Only use suitable screws and appropriate mounting materials.
If specified by the manufacturer or included in the delivery, use screws with locking lacquer
or suitable screw locking.

3. Preparation

Stop the robotic mower completely.
Turn off the device according to the operating manual.
Remove the battery if possible.
Wait until the cutting disc has completely come to a stop.
Carefully turn the robotic mower upside down and place it on a stable, soft surface.
Check the work area for cleanliness and adequate lighting.

4. Disassembly of the Existing Cutting Disc

Loosen the fastening screws of the existing cutting disc.
Completely remove the screws and set them aside safely.
Carefully remove the existing cutting disc from the knife holder.
Clean the knife holder of grass clippings, dirt, and debris.
Check the knife holder for damage or unusual wear.

Warning

Do not use the new cutting disc if the knife holder, fastening points,
threads, or screws are damaged. In this case, the robotic mower may only be reused after proper
inspection.

5. Installation of the CUT GUARD Cutting Disc

Place the CUT GUARD cutting disc correctly on the knife holder.
Ensure that the cutting disc lies flat and is correctly centered.
Insert the appropriate fastening screws.
Tighten the screws evenly and firmly.
Do not overtighten the screws to avoid damage to threads or components.
After installation, check that the cutting disc is securely attached.
Gently turn the cutting disc by hand and check if it runs freely.

6. Installation or Replacement of Replacement Blades

Loosen the screws of the old blades.
Carefully remove the old blades.
Clean the contact surfaces on the cutting disc.
Place the new CUT GUARD replacement blades on the designated fastening points.
Ensure that the blades remain freely movable, as intended by design.
Secure each blade with a suitable screw.
Tighten the screws securely without overtightening.
Check each blade for a secure fit and free movement.

7. Post-Installation Check

Are all screws fully inserted and securely fastened?
Is the cutting disc lying flat and securely?
Can the blades move freely, if intended?
Are there no tools or foreign objects left in the area of the cutting disc?
Does the cutting disc run freely and without grinding?

8. Operation and Maintenance

Regularly check knives, screws, and cutting disc for wear.
Immediately replace damaged or heavily worn parts.
Regularly clean the cutting disc of grass clippings and dirt.
Do not use the robotic mower if unusual noises, vibrations, or running problems occur.
Only use compatible spare parts and suitable mounting materials.

Note on Blade Replacement

Always replace blades in a timely manner. Dull or damaged blades can worsen the cutting quality,
put more strain on the robotic mower, and compromise safety.

9. Disclaimer

CUT GUARD cutting discs, replacement blades, and blades are accessories and spare parts for compatible robotic mowers.
They are not original accessories from the respective device manufacturer unless explicitly stated
in the product description.

The assembly and use are at your own risk. No liability is accepted for damages caused by improper assembly,
incorrect use, damaged components, or failure to observe the operating manual of the robotic mower.

Warning in Case of Injury

Seek medical assistance immediately in case of injury or accident.

GPSR Information on Product Safety

Product safety information in accordance with Regulation (EU) 2023/988 on general product safety.

Manufacturer & Responsible Person (EU)

Patryk Napiorkowski - Trivando

Am bhf Weinhübel 8

02827 Görlitz

Germany

Email:
service@trivando.de

Website:
www.trivando.de

Product Identification

Brand: CUT GUARD

Product Type: Blade discs, replacement blades, and blades for compatible robotic mowers

Intended Use: Accessories and replacement parts for suitable robotic mowers

Product Type: Cutting and fastening components for use in robotic mowers

Item Number / Model / Variant: see respective product description, packaging, or invoice

Compatibility: see product description and operating instructions of the robotic mower

Important Warning

Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Assembly, disassembly, cleaning, and maintenance should only be performed when the robotic mower is completely turned off.
Always wear appropriate protective gloves and wait until the blade disc has come to a complete stop.

Intended Use

CUT GUARD blade discs, replacement blades, and blades are intended solely as accessories and replacement parts for compatible robotic mowers.

The products may only be used for their intended purpose and only in conjunction with suitable, compatible devices.
Any other use, structural modification, or improper assembly may lead to injuries, malfunctions, or property damage.

Not Suitable For

Children.
Persons who have not read or understood the operating instructions of the robotic mower.
Incompatible robotic mowers.
Devices with damaged blade mounts, damaged threads, or defective fastening points.
Use outside the intended application area.
Use as a tool, hand knife, or for other cutting tasks outside the robotic mower.

Safety and Warning Notices

Use only for the intended purpose.
Use only with compatible robotic mowers, suitable blade discs, and appropriate mounting materials.
Always turn off the robotic mower completely before any assembly, disassembly, cleaning, or maintenance.
If possible, remove the battery or disconnect the device from the power supply.
Always wait until the blade disc has come to a complete stop.
Always wear appropriate protective gloves.
Keep hands and feet away from rotating blades.
Never touch knives, blades, or blade discs during operation.
Do not use damaged, bent, heavily worn, rusted, or corroded knives, screws, or blade discs.
Regularly check knives, screws, and blade discs for secure fit, wear, and damage.
Use only suitable screws and appropriate mounting materials.
If provided, use screws with locking lacquer or suitable screw locking.
Keep children, animals, and uninvolved persons away from the work area.
The robotic mower must not be operated if persons, especially children, or animals are in the work area.
In case of unusual noises, vibrations, grinding noises, or running problems, stop operation immediately and check the assembly.
In case of injuries or accidents, seek medical assistance immediately.

Assembly Instructions

Assembly may only be performed when the device is turned off. Always observe the operating instructions of the respective robotic mower.

Blade discs, replacement blades, and blades must be correctly seated and securely fastened. After assembly, check whether the blade disc runs freely and that no tools or foreign objects have been left in the area of the knives.

Check Before Operation

Are all screws fully inserted and tightened?
Is the blade disc correctly centered and securely fastened?
Are the knives correctly mounted?
Can movable knives move freely, if this is structurally intended?
Are there no visible damages?
Does the blade disc run freely and without grinding?

Maintenance and Inspection

Regularly check knives, blades, screws, and blade discs for wear and damage.
Immediately replace damaged or heavily worn parts.
Regularly clean the blade disc of grass residues, dirt, and deposits.
Do not use aggressive cleaning agents that may damage material or coating.
Use only compatible replacement parts and suitable mounting materials.

Storage and Disposal

Store replacement blades, blades, screws, and blade discs dry, clean, and secure.
Keep out of reach of children and unauthorized persons.

Safely package used, damaged, or dull knives and blades to avoid cuts.
Dispose of metal parts, packaging, and accessories in accordance with local regulations.

Note on Original Accessories

CUT GUARD products are compatible accessories and replacement parts. They are not original accessories of the respective
device manufacturer unless explicitly stated in the product description. Brand names, model designations,
and manufacturer information are for compatibility indication only.

Contact for Safety Questions, Complaints, or Accidents

For questions regarding product safety, complaints, accidents, or indications of possible safety issues, please contact us immediately:

Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email: service@trivando.de
Website: www.trivando.de

Frequently asked questions

My VIAX mows regularly—why does the lawn still look brown and dull?

This is the typical look of worn blades: they tear the blades of grass instead of cutting them cleanly. The split tips dry out and turn brown—so from a few meters away, the entire area looks dull. A fresh cutting disc with sharp blades restores the smooth, green-looking cut edges.

Do I need different cutting discs for VIAX 250, VIAX 300, and VIAX 500?

No. All three models use the same blade plate mount, so any version of this cutting disc—whether 6, 7, or 9 blades—fits VIAX 250, 300, and 500 equally. Before ordering, simply compare the model name of your robot and the design of the existing disc.

Can you really see the difference between 6, 7, and 9 blades in the lawn?

Yes, especially on areas you see every day. With 6 blades, you get the proper standard cut; with 7, each blade of grass is captured more often and the area looks denser; with 9 blades, you get the finest cutting pattern in the series—smooth tips that look well maintained even up close. All three variants are installed the same way.

Is the protective cover included only with a certain number of blades?

No, all three versions—6, 7 and 9 blades—are supplied with protection. It keeps the blades securely in position and keeps the grass flow on the disc clear, so that damp grass clippings do not wrap around the blades and slow down rotation. So when switching variants, you don’t have to give anything up.

Do I still need to screw the blades on myself after unpacking?

No. The blades are already firmly mounted on the disc at the time of delivery—depending on the version, 6, 7 or 9 pieces. You take the disc out of the packaging, place it on, and your VIAX can go on to the next round right away with fresh cutting.

How much effort is it to change the cutting disc on the MOVA VIAX?

A matter of just a few minutes: switch off the robot, carefully tilt it, remove the old disc, fit the new one—typically completely without tools. Wear gloves, because even dull blades still have sharp edges. After contact with branches or stones, it’s also worth taking a quick look at the disc.

Who is the set with 60 replacement blades worth it for?

For everyone who wants the lawn to look good every day. Blades inevitably become dull over time—by swapping them with the 60-pack supply, you replace them right away instead of waiting for a reorder, and the cut stays fine throughout the whole season. In the set, the replenishment also costs less than buying individual replacements later.

Is this an original MOVA replacement part?

No, this is a compatible cutting disc from CUT GUARD. It is manufactured to fit precisely the mounting for the mowing disc of MOVA VIAX 250, 300 and 500, is supplied with protection and pre-assembled blades, and is designed for regular use in the robotic mower—an alternative to the original part that can be delivered quickly.

Cutting disc for MOVA VIAX 250, 300 and 500 robotic lawnmowers

Compatibility – MOVA