7-Blade Cutting Disc for Sunseeker V3 & X3 Robotic Lawnmower – Low-Vibration Mowing Disc for Precise Lawn Cutting
- 7-blade cutting disc for Sunseeker V3 and Sunseeker X3 robotic mowers
- Low-vibration cutting plate for smooth operation and precise blade guidance
- Suitable as a mowing plate, cutting plate, or cutting disc for compatible Sunseeker models
- Durable replacement cutting disc for wear, damaged mowing plate, or reduced cutting performance
- Supports a clean, even, and controlled lawn cut during the mowing season
incl. 6 blades
incl. 9 blades
+
+
Compatibility – SUNSEEKER
Fits the following robotic mowers:
- ✓ V3
- ✓ X3
Especially when your SUNSEEKER V3 or X3 feels noticeably “tough” while mowing, this 7-blade cutting disc will restore a clean, even cut—noticeably quieter in operation.
Another fresh-cut look, like it was done by a gardener
Dull blades tear the grass rather than cutting it: the lawn looks uneven, and the mowing disc has to do more work. This also puts strain on the motor, which has to push against the resistance. With the 7-blade cutting disc for SUNSEEKER V3 & X3, you get fresh cutting performance and the cut is back under control. Seven sharp blades provide more cutting points and a finer, more even result—the low-vibration mowing disc runs especially smoothly.
Fits perfectly for your SUNSEEKER V3, among others
The 7-blade cutting disc is suitable for SUNSEEKER V3 and X3 – no guesswork, no tinkering. You can swap the cutting disc on the mowing disc quickly and easily; tools are usually not needed.
Everything included for a quick swap
The 7 blades provide a finer cutting pattern because the grass is captured more evenly. With the additional cutting edges, every blade of grass is picked up more cleanly – the result is a consistently dense area. You get the cutting disc as a complete mowing disc replacement – ready to install for your next job. The swap takes less time than a coffee break: loosen, replace, done.
For a freely running mowing disc
More cutting performance, less “getting stuck”: This helps reduce grass blockages on the mowing disc. Where damp grass would otherwise prevent rotation, sharp cutting edges reliably keep it moving. Result: your SUNSEEKER V3 or X3 runs more reliably, and the lawn cut stays clean even with denser growth. Fewer stops and a calm, precise mowing operation.
The most important points
Top reviews
After trying two other brands, this 7-blade cutting disc for the Sunseeker V3/X3 seems to be a decent match. The fit was correct for my mower, and I noticed less wobble during operation compared with the cheaper set I used before. Cutting is reasonably even, but the first swap took longer than expected because the old disc was pretty stubborn to remove. Shipping was the only real hassle.
After trying out two other brands, this 7-blade cutting disc really reassured me. The installation was simple and the performance is excellent; the result is a neater and more even lawn than ever before. The low-vibration feature is a big plus, making the robotic mower actually operate quieter. These blades also seem sturdier and more durable; I hope they last longer than the previous ones.
Wymieniłem starą tarczę w moim Sunseeker V3 po kilku tygodniach koszenia i od razu było widać różnicę. Nowa 7-klingowa tarcza pracuje dużo spokojniej, a trawnik w moim ok. 400 m² ogrodzie wygląda równo i gęsto, bez poszarpanych końcówek. Montaż był prosty, tylko musiałem dobrze dokręcić śruby, bo inaczej tarcza miała minimalny luz. Po tygodniu użytkowania wszystko działa bez zarzutów i celuję w dłuższą żywotność przy regularnym serwisie.
passar till min sunseeker x3 och märks direkt att den vibrerar mindre än min gamla 6-klingarskiva. jag hade bara lite svårt att få bort den första gångens rostiga skruv, men efter bytet blev snittet jämnare.
Jeg købte 7-klingers messerskiven til min Sunseeker X3, og jeg kunne mærke forskel allerede efter første omgang. I min have på ca. 600 m² ligger der nogle lidt ujævne hjørner, men den nye skive giver et mere ensartet snit og kører roligere end den gamle sløve. Udskiftningen var let, og den sidder fast uden slinger; jeg strammede dog lige efter manualens anvisning for en sikker pasform. Alt i alt et rigtig godt køb til sæsonen.
Installation rapide sur mon Sunseeker X3, sans jeu notable. Le tondeuse vibre moins et la coupe reste nette, même après plusieurs passages.
Write a review
CUT GUARD Assembly Instructions
General assembly instructions for cutting discs, replacement blades, and blades for compatible robotic mowers.
Note
These instructions generally apply to compatible cutting discs, replacement blades, and blades from CUT GUARD.
They do not refer to a specific model or version. Always additionally refer to the operating manual of your robotic mower.
Important Safety Notice
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Always wear appropriate protective gloves during assembly, disassembly, cleaning, and maintenance.
Never work on the cutting disc while it is still moving.
1. General Safety Instructions
- The operator is responsible for accidents, injuries, and damages caused to other persons or their property.
- Keep children, animals, and uninvolved persons away during work and operation of the robotic mower.
- Never touch the cutting disc or the knives while they are still moving.
- Always turn off the robotic mower completely before performing work on the cutting disc or the knives.
- Remove the battery if possible or disconnect the device from the power supply.
- Always wear appropriate protective gloves.
- Do not use damaged, bent, heavily worn, or corroded knives, screws, or cutting discs.
- Regularly check the condition of the knives, fastening screws, and the cutting disc.
2. Required Tools and Materials
- Suitable screwdriver or bit, matching the screws used.
- Protective gloves.
- New or tested fastening screws.
- CUT GUARD cutting disc, replacement blades, or blades.
- Optional: soft surface for safely placing the robotic mower.
Important
Only use suitable screws and appropriate mounting materials.
If specified by the manufacturer or included in the delivery, use screws with locking lacquer
or suitable screw locking.
3. Preparation
- Stop the robotic mower completely.
- Turn off the device according to the operating manual.
- Remove the battery if possible.
- Wait until the cutting disc has completely come to a stop.
- Carefully turn the robotic mower upside down and place it on a stable, soft surface.
- Check the work area for cleanliness and adequate lighting.
4. Disassembly of the Existing Cutting Disc
- Loosen the fastening screws of the existing cutting disc.
- Completely remove the screws and set them aside safely.
- Carefully remove the existing cutting disc from the knife holder.
- Clean the knife holder of grass clippings, dirt, and debris.
- Check the knife holder for damage or unusual wear.
Warning
Do not use the new cutting disc if the knife holder, fastening points,
threads, or screws are damaged. In this case, the robotic mower may only be reused after proper
inspection.
5. Installation of the CUT GUARD Cutting Disc
- Place the CUT GUARD cutting disc correctly on the knife holder.
- Ensure that the cutting disc lies flat and is correctly centered.
- Insert the appropriate fastening screws.
- Tighten the screws evenly and firmly.
- Do not overtighten the screws to avoid damage to threads or components.
- After installation, check that the cutting disc is securely attached.
- Gently turn the cutting disc by hand and check if it runs freely.
6. Installation or Replacement of Replacement Blades
- Loosen the screws of the old blades.
- Carefully remove the old blades.
- Clean the contact surfaces on the cutting disc.
- Place the new CUT GUARD replacement blades on the designated fastening points.
- Ensure that the blades remain freely movable, as intended by design.
- Secure each blade with a suitable screw.
- Tighten the screws securely without overtightening.
- Check each blade for a secure fit and free movement.
7. Post-Installation Check
- Are all screws fully inserted and securely fastened?
- Is the cutting disc lying flat and securely?
- Can the blades move freely, if intended?
- Are there no tools or foreign objects left in the area of the cutting disc?
- Does the cutting disc run freely and without grinding?
8. Operation and Maintenance
- Regularly check knives, screws, and cutting disc for wear.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the cutting disc of grass clippings and dirt.
- Do not use the robotic mower if unusual noises, vibrations, or running problems occur.
- Only use compatible spare parts and suitable mounting materials.
Note on Blade Replacement
Always replace blades in a timely manner. Dull or damaged blades can worsen the cutting quality,
put more strain on the robotic mower, and compromise safety.
9. Disclaimer
CUT GUARD cutting discs, replacement blades, and blades are accessories and spare parts for compatible robotic mowers.
They are not original accessories from the respective device manufacturer unless explicitly stated
in the product description.
The assembly and use are at your own risk. No liability is accepted for damages caused by improper assembly,
incorrect use, damaged components, or failure to observe the operating manual of the robotic mower.
Warning in Case of Injury
Seek medical assistance immediately in case of injury or accident.
GPSR Information on Product Safety
Product safety information in accordance with Regulation (EU) 2023/988 on general product safety.
Manufacturer & Responsible Person (EU)
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email:
service@trivando.de
Website:
www.trivando.de
Product Identification
Brand: CUT GUARD
Product Type: Blade discs, replacement blades, and blades for compatible robotic mowers
Intended Use: Accessories and replacement parts for suitable robotic mowers
Product Type: Cutting and fastening components for use in robotic mowers
Item Number / Model / Variant: see respective product description, packaging, or invoice
Compatibility: see product description and operating instructions of the robotic mower
Important Warning
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Assembly, disassembly, cleaning, and maintenance should only be performed when the robotic mower is completely turned off.
Always wear appropriate protective gloves and wait until the blade disc has come to a complete stop.
Intended Use
CUT GUARD blade discs, replacement blades, and blades are intended solely as accessories and replacement parts for compatible robotic mowers.
The products may only be used for their intended purpose and only in conjunction with suitable, compatible devices.
Any other use, structural modification, or improper assembly may lead to injuries, malfunctions, or property damage.
Not Suitable For
- Children.
- Persons who have not read or understood the operating instructions of the robotic mower.
- Incompatible robotic mowers.
- Devices with damaged blade mounts, damaged threads, or defective fastening points.
- Use outside the intended application area.
- Use as a tool, hand knife, or for other cutting tasks outside the robotic mower.
Safety and Warning Notices
- Use only for the intended purpose.
- Use only with compatible robotic mowers, suitable blade discs, and appropriate mounting materials.
- Always turn off the robotic mower completely before any assembly, disassembly, cleaning, or maintenance.
- If possible, remove the battery or disconnect the device from the power supply.
- Always wait until the blade disc has come to a complete stop.
- Always wear appropriate protective gloves.
- Keep hands and feet away from rotating blades.
- Never touch knives, blades, or blade discs during operation.
- Do not use damaged, bent, heavily worn, rusted, or corroded knives, screws, or blade discs.
- Regularly check knives, screws, and blade discs for secure fit, wear, and damage.
- Use only suitable screws and appropriate mounting materials.
- If provided, use screws with locking lacquer or suitable screw locking.
- Keep children, animals, and uninvolved persons away from the work area.
- The robotic mower must not be operated if persons, especially children, or animals are in the work area.
- In case of unusual noises, vibrations, grinding noises, or running problems, stop operation immediately and check the assembly.
- In case of injuries or accidents, seek medical assistance immediately.
Assembly Instructions
Assembly may only be performed when the device is turned off. Always observe the operating instructions of the respective robotic mower.
Blade discs, replacement blades, and blades must be correctly seated and securely fastened. After assembly, check whether the blade disc runs freely and that no tools or foreign objects have been left in the area of the knives.
Check Before Operation
- Are all screws fully inserted and tightened?
- Is the blade disc correctly centered and securely fastened?
- Are the knives correctly mounted?
- Can movable knives move freely, if this is structurally intended?
- Are there no visible damages?
- Does the blade disc run freely and without grinding?
Maintenance and Inspection
- Regularly check knives, blades, screws, and blade discs for wear and damage.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the blade disc of grass residues, dirt, and deposits.
- Do not use aggressive cleaning agents that may damage material or coating.
- Use only compatible replacement parts and suitable mounting materials.
Storage and Disposal
Store replacement blades, blades, screws, and blade discs dry, clean, and secure.
Keep out of reach of children and unauthorized persons.
Safely package used, damaged, or dull knives and blades to avoid cuts.
Dispose of metal parts, packaging, and accessories in accordance with local regulations.
Note on Original Accessories
CUT GUARD products are compatible accessories and replacement parts. They are not original accessories of the respective
device manufacturer unless explicitly stated in the product description. Brand names, model designations,
and manufacturer information are for compatibility indication only.
Contact for Safety Questions, Complaints, or Accidents
For questions regarding product safety, complaints, accidents, or indications of possible safety issues, please contact us immediately:
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email: service@trivando.de
Website: www.trivando.de
How can I replace the 7-blade cutting disc for my Sunseeker V3 robotic mower?
Replacing the 7-blade cutting disc is done in five simple steps: First, turn off the robotic mower and disconnect it from the power source. Use a wrench to loosen the old cutting disc and carefully remove it. Place the new 7-blade cutting disc onto the holder and tighten the screws. After assembly, the robotic mower should be put back into operation for a short test run. The entire assembly takes about 15-20 minutes.
How long does shipping take for the 7-blade cutting disc for the Sunseeker models, and can I return it?
Shipping of the 7-blade cutting disc for the Sunseeker V3 and X3 usually takes place within 2-3 business days. We also offer a hassle-free return within 30 days if the cutting disc does not meet your expectations. Your satisfaction is important to us, so we are here to assist you quickly and reliably with any inquiries.
How do I know that the 7-blade cutting disc for my Sunseeker X3 robotic mower needs to be replaced?
A replacement of the 7-blade cutting disc should be made if you notice vibrations, unusual noises, or an uneven cutting pattern. Visible damage or signs of wear on the disc are also clear indicators that a replacement is necessary. For these models, precise blade guidance is important to ensure cutting quality.
What common problems occur when using the 7-blade cutting disc for the Sunseeker V3?
Users often report issues such as uneven cutting results or excessive vibrations, indicating a worn or improperly mounted 7-blade cutting disc. Tightening the screws after installation is also often neglected, which can lead to poor blade guidance. Be sure to regularly check the blades and replace the disc at the first signs of problems.
What is the difference between the 7-blade cutting disc for Sunseeker V3 and the 9-blade variant?
The 7-blade cutting disc is ideal for even and precise cuts on regular grass, while the 9-blade variant offers more cutting power for thick or tall grass. So if you have a well-maintained garden with good grass, the 7-blade version is optimal for your Sunseeker V3. In more challenging conditions, the 9-blade variant might be the better choice.