7-blade cutting disc for MOVA 600 & MOVA 1000 robotic lawnmowers – Mowing plate against grass blockages
- 7-blade cutting disc for MOVA 600 and MOVA 1000 robotic lawnmowers
- Especially suitable when grass clippings frequently accumulate on the cutting deck or disrupt rotation
- Supports precise lawn cutting through even blade guidance in the cutting area
- Robust replacement cutting deck for maintenance, replacement, and long-term use during the gardening season
- Also relevant as a blade disc, cutting disc, or robotic lawnmower cutting disc for MOVA models
incl. 7 blades
incl. 9 blades
+
+
Compatibility – MOVA
Fits the following robotic mowers:
- ✓ MOVA 600
- ✓ MOVA 1000
If your MOVA 600 or MOVA 1000 suddenly cuts more slowly and the grass rather “pulls” instead of being cleanly cut, the 7-blade cutting disc is exactly the lever for getting an even cut again.
If MOVA is only tearing the grass instead of cutting it
Dull blades quickly turn every mowing session into a stubborn problem: the grass is cut unevenly, tends to lie down more, and the mowing disc works against resistance. Over time, this also puts strain on the motor, which has to fight through the clogs. With the 7-blade cutting disc for MOVA 600 & MOVA 1000, you restore a fresh cut—and reduce typical grass clogs on the mowing disc. Seven sharp blades provide more cutting points per revolution and a noticeably more even result on your lawn.
Fits your MOVA MOVA 600, among others
The 7-blade cutting disc is specifically designed for MOVA 600 and MOVA 1000. You can replace it quickly without any tedious fiddling—simply swap it for the old cutting disc on the mowing disc.
Delivered ready to install
The 7 blades provide a finer cutting pattern, so the grass is cut more evenly. More cutting edges grasp the blades more precisely and leave you with a dense, well-groomed lawn instead of frayed tips. You get the cutting disc as a complete set for a direct swap on the MOVA mowing disc. The replacement takes only a few minutes and works without tools—remove the old disc, fit the new one, done. Ideal for getting started at the beginning of the season or for quickly replacing worn blades.
Less grass clumping, more drive
More blades mean less “surface area” for blockages: the grass is distributed better and clumps up less often on the mowing disc. Otherwise, damp clippings tend to collect around the blades and slow down rotation— a free-spinning mowing disc keeps the grass flow moving. This helps your MOVA run more reliably even when the grass is a bit denser. Fewer stops, less rework, and a robot that works its routes calmly.
The key points at a glance
Top reviews
Schnell geliefert og passer perfekt til min MOVA 1000. Efter montering slipper den for græsblokader mellem knivene, og klipningen er mere jævn.
Jeg købte 7-klingerskiven til min MOVA 600, fordi der ofte kom græsrester ind og stoppede rotationen. Efter skiftet kører den mere jævnt, og snittet ser ensartet ud. Jeg giver 4 stjerner, fordi der stadig skal lige rengøring til, før den er helt fri for tilstopning.
super remplacement pour mon mova 1000 : la tonte est plus régulière et les herbes se bloquent beaucoup moins. montage rapide, et les 7 lames restent faciles à nettoyer.
I replaced my old cutting disc with this 7-blade cutting disc for MY MOVA 600, and the result has been fantastic! The installation took only 15 minutes, and I have noticed that the grass no longer blocks the blades. Additionally, the quality feels robust, which gives me confidence for long-term use.
Snel geleverd en de 7-klingige messerscheibe past precies op mijn MOVA 600; mijn oude had steeds grasresten tussen de snijrand. De snede is nu gelijkmatiger, maar ik vond de messen iets lastiger om schoon te maken.
Habe die 7-Klingen-Scheibe für meinen MOVA 1000 gekauft, weil sich ständig Grasreste gesammelt haben. Jetzt läuft die Rotation ruhiger und der Schnitt wirkt gleichmäßiger, nur das Reinigen dauert minimal länger.
I replaced the old blade with this 7-blade Messerscheibe for my MOVA 600 and I am thrilled with the result! The installation took me 20 minutes, and the blades now cut the grass evenly and without any clogging issues. You can tell that the material is solid, so I hope it will last a long time.
Achetée pour mon MOVA 600: les herbes restaient souvent coincées et bloquaient la rotation. Après montage, plus de blocages, coupe régulière; livraison rapide et pièce qui se fixe bien.
The blades fit perfectly on my MOVA 1000 and cut grass cleanly with minimal blockage. The only downside was the slow delivery.
Write a review
CUT GUARD Assembly Instructions
General assembly instructions for cutting discs, replacement blades, and blades for compatible robotic mowers.
Note
These instructions generally apply to compatible cutting discs, replacement blades, and blades from CUT GUARD.
They do not refer to a specific model or version. Always additionally refer to the operating manual of your robotic mower.
Important Safety Notice
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Always wear appropriate protective gloves during assembly, disassembly, cleaning, and maintenance.
Never work on the cutting disc while it is still moving.
1. General Safety Instructions
- The operator is responsible for accidents, injuries, and damages caused to other persons or their property.
- Keep children, animals, and uninvolved persons away during work and operation of the robotic mower.
- Never touch the cutting disc or the knives while they are still moving.
- Always turn off the robotic mower completely before performing work on the cutting disc or the knives.
- Remove the battery if possible or disconnect the device from the power supply.
- Always wear appropriate protective gloves.
- Do not use damaged, bent, heavily worn, or corroded knives, screws, or cutting discs.
- Regularly check the condition of the knives, fastening screws, and the cutting disc.
2. Required Tools and Materials
- Suitable screwdriver or bit, matching the screws used.
- Protective gloves.
- New or tested fastening screws.
- CUT GUARD cutting disc, replacement blades, or blades.
- Optional: soft surface for safely placing the robotic mower.
Important
Only use suitable screws and appropriate mounting materials.
If specified by the manufacturer or included in the delivery, use screws with locking lacquer
or suitable screw locking.
3. Preparation
- Stop the robotic mower completely.
- Turn off the device according to the operating manual.
- Remove the battery if possible.
- Wait until the cutting disc has completely come to a stop.
- Carefully turn the robotic mower upside down and place it on a stable, soft surface.
- Check the work area for cleanliness and adequate lighting.
4. Disassembly of the Existing Cutting Disc
- Loosen the fastening screws of the existing cutting disc.
- Completely remove the screws and set them aside safely.
- Carefully remove the existing cutting disc from the knife holder.
- Clean the knife holder of grass clippings, dirt, and debris.
- Check the knife holder for damage or unusual wear.
Warning
Do not use the new cutting disc if the knife holder, fastening points,
threads, or screws are damaged. In this case, the robotic mower may only be reused after proper
inspection.
5. Installation of the CUT GUARD Cutting Disc
- Place the CUT GUARD cutting disc correctly on the knife holder.
- Ensure that the cutting disc lies flat and is correctly centered.
- Insert the appropriate fastening screws.
- Tighten the screws evenly and firmly.
- Do not overtighten the screws to avoid damage to threads or components.
- After installation, check that the cutting disc is securely attached.
- Gently turn the cutting disc by hand and check if it runs freely.
6. Installation or Replacement of Replacement Blades
- Loosen the screws of the old blades.
- Carefully remove the old blades.
- Clean the contact surfaces on the cutting disc.
- Place the new CUT GUARD replacement blades on the designated fastening points.
- Ensure that the blades remain freely movable, as intended by design.
- Secure each blade with a suitable screw.
- Tighten the screws securely without overtightening.
- Check each blade for a secure fit and free movement.
7. Post-Installation Check
- Are all screws fully inserted and securely fastened?
- Is the cutting disc lying flat and securely?
- Can the blades move freely, if intended?
- Are there no tools or foreign objects left in the area of the cutting disc?
- Does the cutting disc run freely and without grinding?
8. Operation and Maintenance
- Regularly check knives, screws, and cutting disc for wear.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the cutting disc of grass clippings and dirt.
- Do not use the robotic mower if unusual noises, vibrations, or running problems occur.
- Only use compatible spare parts and suitable mounting materials.
Note on Blade Replacement
Always replace blades in a timely manner. Dull or damaged blades can worsen the cutting quality,
put more strain on the robotic mower, and compromise safety.
9. Disclaimer
CUT GUARD cutting discs, replacement blades, and blades are accessories and spare parts for compatible robotic mowers.
They are not original accessories from the respective device manufacturer unless explicitly stated
in the product description.
The assembly and use are at your own risk. No liability is accepted for damages caused by improper assembly,
incorrect use, damaged components, or failure to observe the operating manual of the robotic mower.
Warning in Case of Injury
Seek medical assistance immediately in case of injury or accident.
GPSR Information on Product Safety
Product safety information in accordance with Regulation (EU) 2023/988 on general product safety.
Manufacturer & Responsible Person (EU)
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email:
service@trivando.de
Website:
www.trivando.de
Product Identification
Brand: CUT GUARD
Product Type: Blade discs, replacement blades, and blades for compatible robotic mowers
Intended Use: Accessories and replacement parts for suitable robotic mowers
Product Type: Cutting and fastening components for use in robotic mowers
Item Number / Model / Variant: see respective product description, packaging, or invoice
Compatibility: see product description and operating instructions of the robotic mower
Important Warning
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Assembly, disassembly, cleaning, and maintenance should only be performed when the robotic mower is completely turned off.
Always wear appropriate protective gloves and wait until the blade disc has come to a complete stop.
Intended Use
CUT GUARD blade discs, replacement blades, and blades are intended solely as accessories and replacement parts for compatible robotic mowers.
The products may only be used for their intended purpose and only in conjunction with suitable, compatible devices.
Any other use, structural modification, or improper assembly may lead to injuries, malfunctions, or property damage.
Not Suitable For
- Children.
- Persons who have not read or understood the operating instructions of the robotic mower.
- Incompatible robotic mowers.
- Devices with damaged blade mounts, damaged threads, or defective fastening points.
- Use outside the intended application area.
- Use as a tool, hand knife, or for other cutting tasks outside the robotic mower.
Safety and Warning Notices
- Use only for the intended purpose.
- Use only with compatible robotic mowers, suitable blade discs, and appropriate mounting materials.
- Always turn off the robotic mower completely before any assembly, disassembly, cleaning, or maintenance.
- If possible, remove the battery or disconnect the device from the power supply.
- Always wait until the blade disc has come to a complete stop.
- Always wear appropriate protective gloves.
- Keep hands and feet away from rotating blades.
- Never touch knives, blades, or blade discs during operation.
- Do not use damaged, bent, heavily worn, rusted, or corroded knives, screws, or blade discs.
- Regularly check knives, screws, and blade discs for secure fit, wear, and damage.
- Use only suitable screws and appropriate mounting materials.
- If provided, use screws with locking lacquer or suitable screw locking.
- Keep children, animals, and uninvolved persons away from the work area.
- The robotic mower must not be operated if persons, especially children, or animals are in the work area.
- In case of unusual noises, vibrations, grinding noises, or running problems, stop operation immediately and check the assembly.
- In case of injuries or accidents, seek medical assistance immediately.
Assembly Instructions
Assembly may only be performed when the device is turned off. Always observe the operating instructions of the respective robotic mower.
Blade discs, replacement blades, and blades must be correctly seated and securely fastened. After assembly, check whether the blade disc runs freely and that no tools or foreign objects have been left in the area of the knives.
Check Before Operation
- Are all screws fully inserted and tightened?
- Is the blade disc correctly centered and securely fastened?
- Are the knives correctly mounted?
- Can movable knives move freely, if this is structurally intended?
- Are there no visible damages?
- Does the blade disc run freely and without grinding?
Maintenance and Inspection
- Regularly check knives, blades, screws, and blade discs for wear and damage.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the blade disc of grass residues, dirt, and deposits.
- Do not use aggressive cleaning agents that may damage material or coating.
- Use only compatible replacement parts and suitable mounting materials.
Storage and Disposal
Store replacement blades, blades, screws, and blade discs dry, clean, and secure.
Keep out of reach of children and unauthorized persons.
Safely package used, damaged, or dull knives and blades to avoid cuts.
Dispose of metal parts, packaging, and accessories in accordance with local regulations.
Note on Original Accessories
CUT GUARD products are compatible accessories and replacement parts. They are not original accessories of the respective
device manufacturer unless explicitly stated in the product description. Brand names, model designations,
and manufacturer information are for compatibility indication only.
Contact for Safety Questions, Complaints, or Accidents
For questions regarding product safety, complaints, accidents, or indications of possible safety issues, please contact us immediately:
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email: service@trivando.de
Website: www.trivando.de
How can I install the 7-blade cutting disc for my MOVA 600 lawn mower?
To change the cutting disc for the MOVA 600, you will need a wrench. First, make sure that the lawn mower is turned off. Then remove the old disc by loosening the screws with the wrench. Next, place the new 7-blade cutting disc on and tighten the screws. The installation should take about 10-15 minutes.
What happens if I use an incompatible cutting disc for my MOVA 1000?
If you use a wrong or incompatible cutting disc for the MOVA 1000, it can cause an imbalance that overloads the motor. This can lead not only to a poor cutting result but also to damage to the lawn mower itself, such as premature wear of the motor shaft.
Is this 7-blade cutting disc compatible with the MOVA 600 and MOVA 1000 models?
Yes, the 7-blade cutting disc is specifically designed for the MOVA 600 and MOVA 1000 lawn mowers. Make sure you have these models to ensure optimal performance and fit.
What common problems are there with the mowing performance of MOVA 600 and MOVA 1000?
Users often report grass blockages and uneven cutting results with the MOVA 600 and MOVA 1000 models, especially in wet or tall grass. This can be caused by worn or damaged blades, which is why replacing the 7-blade cutting disc is important to maintain performance.
How long does shipping of the cutting disc take and how does the return process work?
Shipping of the 7-blade cutting disc usually takes place within 3-5 business days. If you are not satisfied with the product, you can return it within 30 days as long as it is unused. We offer a hassle-free return policy to make your shopping experience as pleasant as possible.