Cutting disc for ECOVACS GOAT O500, O800, O1200, G1-800 and G1-2000
- cutting disc for ECOVACS GOAT O500, O800, O1200, G1-800 and G1-2000 – five models, one mount
- Three variants to choose from: 6, 7 or 9 blades – the more blades, the finer the cutting edge
- Protection for the mowing disc in every variant – guides the blades and reduces grass blockages
- Blades pre-assembled, tool-free replacement – ready to mow again in just a few minutes
- Optional as a set with 60 replacement blades – refresh sharpness instead of reordering
+
+
+
Compatibility – ECOVACS
Fits the following robotic mowers:
- ✓ GOAT O500
- ✓ GOAT O800
- ✓ GOAT O1200
- ✓ GOAT G1-800
- ✓ GOAT G1-2000
Your ECOVACS GOAT circles with centimeter-precision around flower beds, trees, and garden furniture – but precise navigation helps little when dull blades at the end only tear the grass blades off. Here you will find the right replacement cutting disc for GOAT O500, O800, O1200, G1-800 and G1-2000: with 6, 7 or 9 blades, each variant with blade guard and pre-assembled blades.
6, 7 or 9 blades – how finely should your GOAT cut?
Mechanically, all three versions are the same: they mount on the same attachment and can be installed on any of the five GOAT models. The only difference is how often a blade is hit per rotation – and thus how fine the cut edge turns out at the end.
The classic setup with blade guard. If your GOAT has cut cleanly so far and the disc has simply worn through, you can restore the as-delivered condition – without changing the familiar cut pattern.
Seven cutting points instead of six: Each blade of grass is captured once more per rotation. This is especially noticeable where the lawn grows vigorously and the blades are thicker than in ornamental grass.
Nine blades deliver the finest cut pattern in this series. The clippings are so small that they disappear between the blades of grass – the right choice if you want your lawn to look immaculate even from two meters away.
Precise navigation, imprecise cutting edge
An ECOVACS GOAT detects obstacles, avoids them, and plans the area. However, this intelligence ends exactly where the blade meets the stem: whether you get a clean cut or a crushed fiber is decided solely by the cutting system – no sensor and no app.
After a few weeks of continuous operation, the blade edges wear down. The robotic lawnmower continues to follow its route, but it no longer cuts; it tears: the tips of the stems fray, turn brown after one or two days, and the lawn looks dull instead of fresh despite daily mowing. Many then look for the problem in the settings – but it’s located under the housing.
A fresh cutting disc is the most affordable intervention with which you can noticeably improve cutting quality: no software update, no navigation component—just the exact part where the work actually happens. The disc is delivered with blades already mounted, fitting the mounting for all five GOAT models.
Well-guided blades stay sharp longer
All three versions feature a guard on the mowing disc. It keeps the freely swinging blades on their path and prevents clippings from getting stuck between the disc and the housing. Exactly this grass jam otherwise slows down the rotation—and a blade that turns more slowly cuts worse, no matter how sharp it is.
The swap itself requires no tools: switch off the robotic lawnmower, carefully tilt it, remove the old mowing disc, and attach the new one. Because the blades are delivered already mounted, the individual screwing on of the blades – is also no longer necessary – after two minutes, the GOAT is back on the lawn.
It’s worth taking a quick look underneath the protective frame whenever the robotic lawnmower has hit something solid: stones in the edge area, fallen branches, or forgotten toys leave notches in the blades and can warp the mowing disc – a mowing disc with impact runs unevenly and unnecessarily stresses the mowing unit. The same applies before the winter break, but calmly: brush off grass clippings, check for cracks, and store it dry.
Select the desired number of blades above – 6, 7, or 9, if you like directly together with 60 replacement blades. Each variant fits ECOVACS GOAT O500, O800, O1200, G1-800 and G1-2000 and is delivered ready to install.
Top reviews
The blade department for the ECOVACS GOAT is solid and does its job well, but the packaging was not as sturdy as expected, causing one of the blades to arrive slightly damaged. After trying two other brands, I found that this one offers a better cutting experience, and the included protection is a nice extra. It is a good purchase for anyone who wants to maintain their robotic lawnmower well.
The cutting disc with blade guard fits my ECOVACS GOAT O800 exactly, and it came with 6 replacement blades. I replaced it in about 15 minutes, and only a couple of screws/fasteners need to be handled before it sits perfectly flat. The cutting edge is even again, and no blades feel loose after installation!
Write a review
CUT GUARD Assembly Instructions
General assembly instructions for cutting discs, replacement blades, and blades for compatible robotic mowers.
Note
These instructions generally apply to compatible cutting discs, replacement blades, and blades from CUT GUARD.
They do not refer to a specific model or version. Always additionally refer to the operating manual of your robotic mower.
Important Safety Notice
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Always wear appropriate protective gloves during assembly, disassembly, cleaning, and maintenance.
Never work on the cutting disc while it is still moving.
1. General Safety Instructions
- The operator is responsible for accidents, injuries, and damages caused to other persons or their property.
- Keep children, animals, and uninvolved persons away during work and operation of the robotic mower.
- Never touch the cutting disc or the knives while they are still moving.
- Always turn off the robotic mower completely before performing work on the cutting disc or the knives.
- Remove the battery if possible or disconnect the device from the power supply.
- Always wear appropriate protective gloves.
- Do not use damaged, bent, heavily worn, or corroded knives, screws, or cutting discs.
- Regularly check the condition of the knives, fastening screws, and the cutting disc.
2. Required Tools and Materials
- Suitable screwdriver or bit, matching the screws used.
- Protective gloves.
- New or tested fastening screws.
- CUT GUARD cutting disc, replacement blades, or blades.
- Optional: soft surface for safely placing the robotic mower.
Important
Only use suitable screws and appropriate mounting materials.
If specified by the manufacturer or included in the delivery, use screws with locking lacquer
or suitable screw locking.
3. Preparation
- Stop the robotic mower completely.
- Turn off the device according to the operating manual.
- Remove the battery if possible.
- Wait until the cutting disc has completely come to a stop.
- Carefully turn the robotic mower upside down and place it on a stable, soft surface.
- Check the work area for cleanliness and adequate lighting.
4. Disassembly of the Existing Cutting Disc
- Loosen the fastening screws of the existing cutting disc.
- Completely remove the screws and set them aside safely.
- Carefully remove the existing cutting disc from the knife holder.
- Clean the knife holder of grass clippings, dirt, and debris.
- Check the knife holder for damage or unusual wear.
Warning
Do not use the new cutting disc if the knife holder, fastening points,
threads, or screws are damaged. In this case, the robotic mower may only be reused after proper
inspection.
5. Installation of the CUT GUARD Cutting Disc
- Place the CUT GUARD cutting disc correctly on the knife holder.
- Ensure that the cutting disc lies flat and is correctly centered.
- Insert the appropriate fastening screws.
- Tighten the screws evenly and firmly.
- Do not overtighten the screws to avoid damage to threads or components.
- After installation, check that the cutting disc is securely attached.
- Gently turn the cutting disc by hand and check if it runs freely.
6. Installation or Replacement of Replacement Blades
- Loosen the screws of the old blades.
- Carefully remove the old blades.
- Clean the contact surfaces on the cutting disc.
- Place the new CUT GUARD replacement blades on the designated fastening points.
- Ensure that the blades remain freely movable, as intended by design.
- Secure each blade with a suitable screw.
- Tighten the screws securely without overtightening.
- Check each blade for a secure fit and free movement.
7. Post-Installation Check
- Are all screws fully inserted and securely fastened?
- Is the cutting disc lying flat and securely?
- Can the blades move freely, if intended?
- Are there no tools or foreign objects left in the area of the cutting disc?
- Does the cutting disc run freely and without grinding?
8. Operation and Maintenance
- Regularly check knives, screws, and cutting disc for wear.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the cutting disc of grass clippings and dirt.
- Do not use the robotic mower if unusual noises, vibrations, or running problems occur.
- Only use compatible spare parts and suitable mounting materials.
Note on Blade Replacement
Always replace blades in a timely manner. Dull or damaged blades can worsen the cutting quality,
put more strain on the robotic mower, and compromise safety.
9. Disclaimer
CUT GUARD cutting discs, replacement blades, and blades are accessories and spare parts for compatible robotic mowers.
They are not original accessories from the respective device manufacturer unless explicitly stated
in the product description.
The assembly and use are at your own risk. No liability is accepted for damages caused by improper assembly,
incorrect use, damaged components, or failure to observe the operating manual of the robotic mower.
Warning in Case of Injury
Seek medical assistance immediately in case of injury or accident.
GPSR Information on Product Safety
Product safety information in accordance with Regulation (EU) 2023/988 on general product safety.
Manufacturer & Responsible Person (EU)
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email:
service@trivando.de
Website:
www.trivando.de
Product Identification
Brand: CUT GUARD
Product Type: Blade discs, replacement blades, and blades for compatible robotic mowers
Intended Use: Accessories and replacement parts for suitable robotic mowers
Product Type: Cutting and fastening components for use in robotic mowers
Item Number / Model / Variant: see respective product description, packaging, or invoice
Compatibility: see product description and operating instructions of the robotic mower
Important Warning
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Assembly, disassembly, cleaning, and maintenance should only be performed when the robotic mower is completely turned off.
Always wear appropriate protective gloves and wait until the blade disc has come to a complete stop.
Intended Use
CUT GUARD blade discs, replacement blades, and blades are intended solely as accessories and replacement parts for compatible robotic mowers.
The products may only be used for their intended purpose and only in conjunction with suitable, compatible devices.
Any other use, structural modification, or improper assembly may lead to injuries, malfunctions, or property damage.
Not Suitable For
- Children.
- Persons who have not read or understood the operating instructions of the robotic mower.
- Incompatible robotic mowers.
- Devices with damaged blade mounts, damaged threads, or defective fastening points.
- Use outside the intended application area.
- Use as a tool, hand knife, or for other cutting tasks outside the robotic mower.
Safety and Warning Notices
- Use only for the intended purpose.
- Use only with compatible robotic mowers, suitable blade discs, and appropriate mounting materials.
- Always turn off the robotic mower completely before any assembly, disassembly, cleaning, or maintenance.
- If possible, remove the battery or disconnect the device from the power supply.
- Always wait until the blade disc has come to a complete stop.
- Always wear appropriate protective gloves.
- Keep hands and feet away from rotating blades.
- Never touch knives, blades, or blade discs during operation.
- Do not use damaged, bent, heavily worn, rusted, or corroded knives, screws, or blade discs.
- Regularly check knives, screws, and blade discs for secure fit, wear, and damage.
- Use only suitable screws and appropriate mounting materials.
- If provided, use screws with locking lacquer or suitable screw locking.
- Keep children, animals, and uninvolved persons away from the work area.
- The robotic mower must not be operated if persons, especially children, or animals are in the work area.
- In case of unusual noises, vibrations, grinding noises, or running problems, stop operation immediately and check the assembly.
- In case of injuries or accidents, seek medical assistance immediately.
Assembly Instructions
Assembly may only be performed when the device is turned off. Always observe the operating instructions of the respective robotic mower.
Blade discs, replacement blades, and blades must be correctly seated and securely fastened. After assembly, check whether the blade disc runs freely and that no tools or foreign objects have been left in the area of the knives.
Check Before Operation
- Are all screws fully inserted and tightened?
- Is the blade disc correctly centered and securely fastened?
- Are the knives correctly mounted?
- Can movable knives move freely, if this is structurally intended?
- Are there no visible damages?
- Does the blade disc run freely and without grinding?
Maintenance and Inspection
- Regularly check knives, blades, screws, and blade discs for wear and damage.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the blade disc of grass residues, dirt, and deposits.
- Do not use aggressive cleaning agents that may damage material or coating.
- Use only compatible replacement parts and suitable mounting materials.
Storage and Disposal
Store replacement blades, blades, screws, and blade discs dry, clean, and secure.
Keep out of reach of children and unauthorized persons.
Safely package used, damaged, or dull knives and blades to avoid cuts.
Dispose of metal parts, packaging, and accessories in accordance with local regulations.
Note on Original Accessories
CUT GUARD products are compatible accessories and replacement parts. They are not original accessories of the respective
device manufacturer unless explicitly stated in the product description. Brand names, model designations,
and manufacturer information are for compatibility indication only.
Contact for Safety Questions, Complaints, or Accidents
For questions regarding product safety, complaints, accidents, or indications of possible safety issues, please contact us immediately:
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email: service@trivando.de
Website: www.trivando.de
Frequently asked questions
Does a disc really fit all GOAT models from O500 to G1-2000?
Yes. ECOVACS uses the same mowing disc mount for the GOAT O500, O800, O1200, G1-800 and G1-2000, so each of the three variants fits without any adapter or modification. However, please compare the model name on your robot and the design of the installed cutting disc before placing your order.
My GOAT navigates perfectly, yet the lawn looks dull. What could be the reason?
Navigation and cutting quality are two separate things. The robot can plan its routes perfectly and steer around obstacles cleanly—whether the blade cuts the stalk smoothly at the end or only crushes it is determined solely by the blade. Rounded cutting edges can be recognized by frayed stalk tips that start turning brown after one to two days. In that case, adjusting in the app won’t help—what you need is a fresh mowing disc.
Which blade count should I choose for my GOAT—6, 7, or 9?
The 6-blade variant is the direct replacement and restores the familiar condition. The 7-blade variant provides one additional cutting point per revolution and reliably handles vigorously grown, thicker stalks. The 9-blade variant delivers the finest cutting edge and the best mulching effect. All three can be installed the same way—it’s only about the desired cutting result.
Do the 7- and 9-blade variants also have protection on the disc?
Yes, all three versions are supplied with protection for the mowing disc; for the 6-blade version, it is the classic blade guard. The guard guides the freely swinging blades along their path and prevents moist clippings from getting stuck between the blades and the housing, slowing down rotation.
Do I need tools or any handyman skills to change it?
Neither. You switch the GOAT off, carefully tilt it, remove the old mowing disc, and fit the new one on—without a screwdriver. Since the blades are already pre-assembled, there is also no need to individually screw in the blades. The whole process takes only a few minutes; please wear gloves during this time.
Are the blades already mounted on the disc?
Yes. Each disc comes pre-installed with blades— the 6-blade version with 6, the 7-blade version with 7, and the 9-blade version with 9 already mounted blades. So you don’t receive a loose bag of replacement blades to screw on, but a complete mowing disc that you can place directly onto the robot straight from the packaging.
When is the set with 60 replacement blades worth it?
When your GOAT runs regularly. The disc itself lasts significantly longer under normal use than the sharpness of the blades on it—sharpness is the actual consumable. With the 60-blade set, you can add fresh blades as soon as the cutting edge starts to wear down, without having to wait for a delivery in the middle of the season. The unit price in the set is lower than that of a later individual purchase.
Is this an original replacement part from ECOVACS?
No, it is a compatible cutting disc from CUT GUARD. It is manufactured to fit precisely the mounting for the GOAT models O500, O800, O1200, G1-800 and G1-2000, and is designed for continuous operation in the robotic mower — an alternative to the original part, with pre-assembled blades and optionally with 7 or 9 blades, which are not available from the factory like that.