Cutting disc for Mammotion Yuka Mini and Yuka Mini 2
- Cutting disc for Mammotion YUKA Mini and YUKA Mini 2 robotic lawnmowers
- Three variants to choose from: 6, 7 or 9 blades – the more blades, the finer the cutting pattern
- Blades already mounted – ready to use right away, no accessories needed
- Less likely to get blocked by grass and supports an even lawn cut
- Optional as a set with 60 replacement blades – cheaper than buying individually
+
+
+
Compatibility – Mammotion
Fits the following robotic mowers:
- ✓ Yuka Mini
- ✓ Yuka Mini 2
If your Mammotion Yuka Mini or Yuka Mini 2 suddenly cuts more sluggishly, it is almost always due to the cutting disc. Here you choose how finely it should be cut – with 6, 7 or 9 blades, each with pre-assembled blades.
Which blade count is right for your lawn?
All three versions fit mechanically identical on the Yuka Mini and Yuka Mini 2. The difference lies in the cut pattern: the more blades, the finer and more even the grass is cut.
The right choice for well-kept, regularly mowed areas. As the only variant with mounted blade guard: it prevents clippings from building up between the blades and blocking them.
One more blade distributes the cutting work across more cutting. This is useful when the grass grows more vigorously between two mowing cycles or when the area is somewhat overgrown.
The highest cutting density – for dense, strong grass and larger areas. During mulching, the cuttings are finely chopped and spread more evenly across the lawn.
Unpack, attach, and start mowing
For replacement, you don’t need any special tools: switch off the robotic lawnmower, turn it over carefully, unscrew the old disc, and mount the new one – a suitable screwdriver is all you need.
Here’s how to proceed: switch off the robot, place it on a soft surface, and loosen the screws of the old mowing disc. Fit the new disc, tighten the screws firmly by hand – done. The complete swap takes hardly five minutes and works identically for the Yuka Mini and Yuka Mini 2.
Make sure the blades remain freely movable and can rotate smoothly. They should be able to pivot during operation – only then does the cutting system work evenly and the cut pattern stays clean.
A good time for a quick maintenance check: if the robotic lawnmower is already lying on its back, it’s worth clearing the underside of the housing and the area around the wheels of grass clippings. It takes just a moment and keeps the cutting system clear permanently.
How you can tell when a replacement is due
Brown, frayed tufts of grass after mowing, an uneven cut pattern, or a noticeably louder-running motor are the typical signs. Visible notches and deformations on the blades also indicate that a replacement is needed.
After a collision with a solid obstacle, it’s worth taking a look at the disc: even a slightly bent cutting disc leads to imbalance, makes the robotic lawnmower noticeably louder, and permanently puts strain on the bearings.
Dull blades no longer cut – they tear. The frayed blades dry out at the tips, the lawn looks brown, and it’s put under stress. Often, people then fertilize or additionally water, even though a simple blade or disc replacement solves the problem.
As a rule of thumb: replace blades every four to eight weeks, depending on lawn area and mowing frequency, and check the cutting disc itself once per season. With the optional 60er Klingen Set, you’ll have the replenishment right on hand.
Precisely fitting for Mammotion Yuka Mini and Yuka Mini 2
These cutting discs are manufactured to fit precisely for the Yuka Mini series – for Yuka Mini (500, 800) as well as for Yuka Mini 2 (500, 1000). The mounting matches the original; you do not need to make any adjustments or drill anything out.
Whether as replacement mowing disc, blade plate or cutting disc: The discs are equally suitable for maintenance, repair, and preparing for the new mowing season. A quick check of blades and fasteners every few weeks keeps cutting performance consistent and helps prevent larger damage.
Top reviews
Fits my Mammotion Yuka Mini 2, and the blade guard gives a better feel during operation. However, I had to adjust the replacement of the blade a bit before it sat completely steady.
I ordered the cutting disc for my Mammotion Yuka Mini 2 because after a few weeks of mowing, the old blades slowly started to lose their sharpness. With the blade guard, everything runs more smoothly, and the 6 replacement blades were perfect for a quick swap. In my small townhouse garden, the robotic mower delivers a noticeably more even cut, even when the grass is a bit higher. The fit was as expected; the only thing is that assembling the new blades takes me a little longer than I thought.
Write a review
CUT GUARD Assembly Instructions
General assembly instructions for cutting discs, replacement blades, and blades for compatible robotic mowers.
Note
These instructions generally apply to compatible cutting discs, replacement blades, and blades from CUT GUARD.
They do not refer to a specific model or version. Always additionally refer to the operating manual of your robotic mower.
Important Safety Notice
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Always wear appropriate protective gloves during assembly, disassembly, cleaning, and maintenance.
Never work on the cutting disc while it is still moving.
1. General Safety Instructions
- The operator is responsible for accidents, injuries, and damages caused to other persons or their property.
- Keep children, animals, and uninvolved persons away during work and operation of the robotic mower.
- Never touch the cutting disc or the knives while they are still moving.
- Always turn off the robotic mower completely before performing work on the cutting disc or the knives.
- Remove the battery if possible or disconnect the device from the power supply.
- Always wear appropriate protective gloves.
- Do not use damaged, bent, heavily worn, or corroded knives, screws, or cutting discs.
- Regularly check the condition of the knives, fastening screws, and the cutting disc.
2. Required Tools and Materials
- Suitable screwdriver or bit, matching the screws used.
- Protective gloves.
- New or tested fastening screws.
- CUT GUARD cutting disc, replacement blades, or blades.
- Optional: soft surface for safely placing the robotic mower.
Important
Only use suitable screws and appropriate mounting materials.
If specified by the manufacturer or included in the delivery, use screws with locking lacquer
or suitable screw locking.
3. Preparation
- Stop the robotic mower completely.
- Turn off the device according to the operating manual.
- Remove the battery if possible.
- Wait until the cutting disc has completely come to a stop.
- Carefully turn the robotic mower upside down and place it on a stable, soft surface.
- Check the work area for cleanliness and adequate lighting.
4. Disassembly of the Existing Cutting Disc
- Loosen the fastening screws of the existing cutting disc.
- Completely remove the screws and set them aside safely.
- Carefully remove the existing cutting disc from the knife holder.
- Clean the knife holder of grass clippings, dirt, and debris.
- Check the knife holder for damage or unusual wear.
Warning
Do not use the new cutting disc if the knife holder, fastening points,
threads, or screws are damaged. In this case, the robotic mower may only be reused after proper
inspection.
5. Installation of the CUT GUARD Cutting Disc
- Place the CUT GUARD cutting disc correctly on the knife holder.
- Ensure that the cutting disc lies flat and is correctly centered.
- Insert the appropriate fastening screws.
- Tighten the screws evenly and firmly.
- Do not overtighten the screws to avoid damage to threads or components.
- After installation, check that the cutting disc is securely attached.
- Gently turn the cutting disc by hand and check if it runs freely.
6. Installation or Replacement of Replacement Blades
- Loosen the screws of the old blades.
- Carefully remove the old blades.
- Clean the contact surfaces on the cutting disc.
- Place the new CUT GUARD replacement blades on the designated fastening points.
- Ensure that the blades remain freely movable, as intended by design.
- Secure each blade with a suitable screw.
- Tighten the screws securely without overtightening.
- Check each blade for a secure fit and free movement.
7. Post-Installation Check
- Are all screws fully inserted and securely fastened?
- Is the cutting disc lying flat and securely?
- Can the blades move freely, if intended?
- Are there no tools or foreign objects left in the area of the cutting disc?
- Does the cutting disc run freely and without grinding?
8. Operation and Maintenance
- Regularly check knives, screws, and cutting disc for wear.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the cutting disc of grass clippings and dirt.
- Do not use the robotic mower if unusual noises, vibrations, or running problems occur.
- Only use compatible spare parts and suitable mounting materials.
Note on Blade Replacement
Always replace blades in a timely manner. Dull or damaged blades can worsen the cutting quality,
put more strain on the robotic mower, and compromise safety.
9. Disclaimer
CUT GUARD cutting discs, replacement blades, and blades are accessories and spare parts for compatible robotic mowers.
They are not original accessories from the respective device manufacturer unless explicitly stated
in the product description.
The assembly and use are at your own risk. No liability is accepted for damages caused by improper assembly,
incorrect use, damaged components, or failure to observe the operating manual of the robotic mower.
Warning in Case of Injury
Seek medical assistance immediately in case of injury or accident.
GPSR Information on Product Safety
Product safety information in accordance with Regulation (EU) 2023/988 on general product safety.
Manufacturer & Responsible Person (EU)
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email:
service@trivando.de
Website:
www.trivando.de
Product Identification
Brand: CUT GUARD
Product Type: Blade discs, replacement blades, and blades for compatible robotic mowers
Intended Use: Accessories and replacement parts for suitable robotic mowers
Product Type: Cutting and fastening components for use in robotic mowers
Item Number / Model / Variant: see respective product description, packaging, or invoice
Compatibility: see product description and operating instructions of the robotic mower
Important Warning
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Assembly, disassembly, cleaning, and maintenance should only be performed when the robotic mower is completely turned off.
Always wear appropriate protective gloves and wait until the blade disc has come to a complete stop.
Intended Use
CUT GUARD blade discs, replacement blades, and blades are intended solely as accessories and replacement parts for compatible robotic mowers.
The products may only be used for their intended purpose and only in conjunction with suitable, compatible devices.
Any other use, structural modification, or improper assembly may lead to injuries, malfunctions, or property damage.
Not Suitable For
- Children.
- Persons who have not read or understood the operating instructions of the robotic mower.
- Incompatible robotic mowers.
- Devices with damaged blade mounts, damaged threads, or defective fastening points.
- Use outside the intended application area.
- Use as a tool, hand knife, or for other cutting tasks outside the robotic mower.
Safety and Warning Notices
- Use only for the intended purpose.
- Use only with compatible robotic mowers, suitable blade discs, and appropriate mounting materials.
- Always turn off the robotic mower completely before any assembly, disassembly, cleaning, or maintenance.
- If possible, remove the battery or disconnect the device from the power supply.
- Always wait until the blade disc has come to a complete stop.
- Always wear appropriate protective gloves.
- Keep hands and feet away from rotating blades.
- Never touch knives, blades, or blade discs during operation.
- Do not use damaged, bent, heavily worn, rusted, or corroded knives, screws, or blade discs.
- Regularly check knives, screws, and blade discs for secure fit, wear, and damage.
- Use only suitable screws and appropriate mounting materials.
- If provided, use screws with locking lacquer or suitable screw locking.
- Keep children, animals, and uninvolved persons away from the work area.
- The robotic mower must not be operated if persons, especially children, or animals are in the work area.
- In case of unusual noises, vibrations, grinding noises, or running problems, stop operation immediately and check the assembly.
- In case of injuries or accidents, seek medical assistance immediately.
Assembly Instructions
Assembly may only be performed when the device is turned off. Always observe the operating instructions of the respective robotic mower.
Blade discs, replacement blades, and blades must be correctly seated and securely fastened. After assembly, check whether the blade disc runs freely and that no tools or foreign objects have been left in the area of the knives.
Check Before Operation
- Are all screws fully inserted and tightened?
- Is the blade disc correctly centered and securely fastened?
- Are the knives correctly mounted?
- Can movable knives move freely, if this is structurally intended?
- Are there no visible damages?
- Does the blade disc run freely and without grinding?
Maintenance and Inspection
- Regularly check knives, blades, screws, and blade discs for wear and damage.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the blade disc of grass residues, dirt, and deposits.
- Do not use aggressive cleaning agents that may damage material or coating.
- Use only compatible replacement parts and suitable mounting materials.
Storage and Disposal
Store replacement blades, blades, screws, and blade discs dry, clean, and secure.
Keep out of reach of children and unauthorized persons.
Safely package used, damaged, or dull knives and blades to avoid cuts.
Dispose of metal parts, packaging, and accessories in accordance with local regulations.
Note on Original Accessories
CUT GUARD products are compatible accessories and replacement parts. They are not original accessories of the respective
device manufacturer unless explicitly stated in the product description. Brand names, model designations,
and manufacturer information are for compatibility indication only.
Contact for Safety Questions, Complaints, or Accidents
For questions regarding product safety, complaints, accidents, or indications of possible safety issues, please contact us immediately:
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email: service@trivando.de
Website: www.trivando.de
Frequently asked questions
Which number of blades should I choose – 6, 7, or 9?
All three variants fit identically on the Yuka Mini and Yuka Mini 2 – the difference lies in the cutting pattern. The 6-blade variant is the proven standard for well-maintained areas, 7 blades provide a denser cutting pattern with stronger growth, and 9 blades deliver the finest cut in dense grass and larger areas. If you’re unsure, you’re best off with 6 or 7 blades.
Does the cutting disc fit both models – Yuka Mini and Yuka Mini 2?
Yes. The mounting matches the original and fits the Yuka Mini (500, 800) as well as the Yuka Mini 2 (500, 1000). No adjustment or re-drilling is necessary.
Does each variant have a blade guard?
No – the installed blade guard belongs to the 6-blade variant. It prevents cut grass from getting stuck between the blades and blocking them. The versions with 7 and 9 blades are supplied without a blade guard.
What do I get from the set with 60 replacement blades?
Blades are wear parts and should be replaced about every four to eight weeks depending on the lawn area. With the 60-piece set, you have plenty of blades at home for the entire season and pay significantly less as a set than when buying individually. The set is available for each of the three blade counts.
How do I replace the cutting disc and how long does it take?
Switch off the robot, turn it over carefully, unscrew the old disc and mount the new one—just a suitable screwdriver is enough. In practice, the complete replacement takes only a few minutes and works identically for the Yuka Mini and Yuka Mini 2.
How do I know when a replacement is due?
Typical signs are brown, frayed grass tips after mowing, an uneven cutting pattern, or a motor that is noticeably louder during operation. Visible notches on the blades or a collision with a solid obstacle are also a good reason to take a closer look.
What distinguishes the CUT GUARD cutting disc from the original?
You get the perfectly fitting alternative at a lower price—and with 7 or 9 blades it even delivers a denser cutting pattern than the original disc. All variants are supplied with mounted blades and are ready to use right away.
Can the cutting disc stay on the robot over the winter?
Yes, it can remain mounted. However, before storing it, you should thoroughly remove any grass residue and moisture so that the blades and the mounting do not suffer during the winter break.