9-Blade Cutting Disc for Sunseeker V3 & X3 Robotic Lawnmowers – Low-Vibration Precision Mowing Disc
- 9-Blade Cutting Disc for Sunseeker V3 and Sunseeker X3 Robotic Lawnmowers
- More cutting points for a finer cut and an even lawn surface
- Low-vibration precision mowing disc for smooth operation and stable blade guidance
- Suitable as a blade disc, mowing disc, or cutting disc for compatible Sunseeker models
- Durable replacement cutting disc for maintenance, replacement, and precise lawn care
incl. 9 blades
+
Compatibility – SUNSEEKER
Fits the following robotic mowers:
- ✓ V3
- ✓ X3
More quiet during operation: With the 9-blade cutting disc from SUNSEEKER for Sunseeker V3 & X3, you get a clean cut and noticeably less vibration on the mowing disc.
Why the lawn suddenly looks unkempt
When the blades become dull, the Sunseeker V3 or X3 tears the grass instead of cutting it cleanly—resulting in uneven edges and more rework. After a while, the sharpness fades, and the lawn looks frayed rather than well-groomed. This 9-blade cutting disc restores cutting performance and ensures your lawn is evenly “cut through” again. Nine sharp blades provide the finest cutting pattern for this series—the low-vibration precision mowing disc runs especially smoothly.
Fits perfectly for your SUNSEEKER V3 and others
The 9-blade cutting disc is compatible with Sunseeker V3 & X3 and fits exactly where it belongs—no tinkering required. The swap is quick: remove the old cutting disc, attach the new one—you save yourself the tool change and the long trial-and-error.
Ready for use in just a few minutes
The 9 blades work precisely and distribute the cut more evenly across the mowing disc. The more cutting edges work simultaneously, the denser and more even the lawn looks—also up close. You receive the cutting disc as a complete set—so the replacement is done in one step and you can start again with full cutting power. The swap takes only a few minutes, completely without tools.
No more getting stuck in dense grass
With the sharp blades, the grass is captured more cleanly, resulting in less “pulling” and fewer blockages on the mowing disc. Otherwise, damp clippings collect around the blades and slow down the rotation—an overrunning mowing disc keeps the flow of grass moving. This helps your Sunseeker V3 or X3 run more reliably, even when the grass is a bit thicker. Less vibration, fewer stops, and a consistently well-kept lawn.
That’s why the switch is worth it
Top reviews
Wymieniłam talerz tnący w moim Sunseeker V3 i od razu czuć mniejszą wibrację. Trawnik po koszeniu wygląda równo, a montaż był szybki.
Deze 9-Klingen-Messerscheibe pastte bij mijn Sunseeker X3 zoals verwacht; ik telde ook echt alle 9 snijpunten. Het loopt rustiger met minder trilling en de snede oogt gelijkmatiger. Installatie ging vlot, maar ik had graag wat duidelijkere volgorde bij het los- en vastzetten van de schroeven gezien; daardoor duurde het bij mij ~20 minuten.
den passer perfekt til min sunseeker v3, og den kører mærkbart roligere med mindre vibration. græsset får en mere jævn kant efter klipning.
Quick delivery and the 9-blade disc fit my Sunseeker V3 perfectly. It runs noticeably calmer, but the installation instructions could be clearer.
Ich habe die 9-Klingen-Messerscheibe für meinen Sunseeker V3 nach ein paar Monaten Nutzung gewechselt und sie macht einen deutlich ruhigeren Lauf als die alte Scheibe. Auf meinem gut 600-m²-Garten bekomme ich damit ein gleichmäßigeres Schnittbild, besonders an den Rändern und in den etwas widerspenstigen Stellen. Die Montage war grundsätzlich ok, aber ich musste die Schrauben doch einmal nachziehen, damit alles sauber saß. Insgesamt trotzdem eine lohnende Ersatzscheibe, 4 out of 5 Sternen.
Depuis que j’ai remplacé la lame d’origine de mon Sunseeker V3 par cette 9-Klingen-Messerscheibe, la coupe de mon jardin se voit vraiment plus régulière, surtout sur les zones où l’herbe est un peu dense (j’ai environ 500 m²). Le disque à 9 lames tourne avec beaucoup moins de vibrations, et on sent que la trajectoire est plus stable. L’installation a été simple une fois la pièce en place, et la coupe tient bien dans le temps.
Works really well, cuts evenly and neatly with good stability. Significantly less vibration than before.
Write a review
CUT GUARD Assembly Instructions
General assembly instructions for cutting discs, replacement blades, and blades for compatible robotic mowers.
Note
These instructions generally apply to compatible cutting discs, replacement blades, and blades from CUT GUARD.
They do not refer to a specific model or version. Always additionally refer to the operating manual of your robotic mower.
Important Safety Notice
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Always wear appropriate protective gloves during assembly, disassembly, cleaning, and maintenance.
Never work on the cutting disc while it is still moving.
1. General Safety Instructions
- The operator is responsible for accidents, injuries, and damages caused to other persons or their property.
- Keep children, animals, and uninvolved persons away during work and operation of the robotic mower.
- Never touch the cutting disc or the knives while they are still moving.
- Always turn off the robotic mower completely before performing work on the cutting disc or the knives.
- Remove the battery if possible or disconnect the device from the power supply.
- Always wear appropriate protective gloves.
- Do not use damaged, bent, heavily worn, or corroded knives, screws, or cutting discs.
- Regularly check the condition of the knives, fastening screws, and the cutting disc.
2. Required Tools and Materials
- Suitable screwdriver or bit, matching the screws used.
- Protective gloves.
- New or tested fastening screws.
- CUT GUARD cutting disc, replacement blades, or blades.
- Optional: soft surface for safely placing the robotic mower.
Important
Only use suitable screws and appropriate mounting materials.
If specified by the manufacturer or included in the delivery, use screws with locking lacquer
or suitable screw locking.
3. Preparation
- Stop the robotic mower completely.
- Turn off the device according to the operating manual.
- Remove the battery if possible.
- Wait until the cutting disc has completely come to a stop.
- Carefully turn the robotic mower upside down and place it on a stable, soft surface.
- Check the work area for cleanliness and adequate lighting.
4. Disassembly of the Existing Cutting Disc
- Loosen the fastening screws of the existing cutting disc.
- Completely remove the screws and set them aside safely.
- Carefully remove the existing cutting disc from the knife holder.
- Clean the knife holder of grass clippings, dirt, and debris.
- Check the knife holder for damage or unusual wear.
Warning
Do not use the new cutting disc if the knife holder, fastening points,
threads, or screws are damaged. In this case, the robotic mower may only be reused after proper
inspection.
5. Installation of the CUT GUARD Cutting Disc
- Place the CUT GUARD cutting disc correctly on the knife holder.
- Ensure that the cutting disc lies flat and is correctly centered.
- Insert the appropriate fastening screws.
- Tighten the screws evenly and firmly.
- Do not overtighten the screws to avoid damage to threads or components.
- After installation, check that the cutting disc is securely attached.
- Gently turn the cutting disc by hand and check if it runs freely.
6. Installation or Replacement of Replacement Blades
- Loosen the screws of the old blades.
- Carefully remove the old blades.
- Clean the contact surfaces on the cutting disc.
- Place the new CUT GUARD replacement blades on the designated fastening points.
- Ensure that the blades remain freely movable, as intended by design.
- Secure each blade with a suitable screw.
- Tighten the screws securely without overtightening.
- Check each blade for a secure fit and free movement.
7. Post-Installation Check
- Are all screws fully inserted and securely fastened?
- Is the cutting disc lying flat and securely?
- Can the blades move freely, if intended?
- Are there no tools or foreign objects left in the area of the cutting disc?
- Does the cutting disc run freely and without grinding?
8. Operation and Maintenance
- Regularly check knives, screws, and cutting disc for wear.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the cutting disc of grass clippings and dirt.
- Do not use the robotic mower if unusual noises, vibrations, or running problems occur.
- Only use compatible spare parts and suitable mounting materials.
Note on Blade Replacement
Always replace blades in a timely manner. Dull or damaged blades can worsen the cutting quality,
put more strain on the robotic mower, and compromise safety.
9. Disclaimer
CUT GUARD cutting discs, replacement blades, and blades are accessories and spare parts for compatible robotic mowers.
They are not original accessories from the respective device manufacturer unless explicitly stated
in the product description.
The assembly and use are at your own risk. No liability is accepted for damages caused by improper assembly,
incorrect use, damaged components, or failure to observe the operating manual of the robotic mower.
Warning in Case of Injury
Seek medical assistance immediately in case of injury or accident.
GPSR Information on Product Safety
Product safety information in accordance with Regulation (EU) 2023/988 on general product safety.
Manufacturer & Responsible Person (EU)
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email:
service@trivando.de
Website:
www.trivando.de
Product Identification
Brand: CUT GUARD
Product Type: Blade discs, replacement blades, and blades for compatible robotic mowers
Intended Use: Accessories and replacement parts for suitable robotic mowers
Product Type: Cutting and fastening components for use in robotic mowers
Item Number / Model / Variant: see respective product description, packaging, or invoice
Compatibility: see product description and operating instructions of the robotic mower
Important Warning
Sharp blades. Risk of injury. The knives and blades can cause serious cuts.
Assembly, disassembly, cleaning, and maintenance should only be performed when the robotic mower is completely turned off.
Always wear appropriate protective gloves and wait until the blade disc has come to a complete stop.
Intended Use
CUT GUARD blade discs, replacement blades, and blades are intended solely as accessories and replacement parts for compatible robotic mowers.
The products may only be used for their intended purpose and only in conjunction with suitable, compatible devices.
Any other use, structural modification, or improper assembly may lead to injuries, malfunctions, or property damage.
Not Suitable For
- Children.
- Persons who have not read or understood the operating instructions of the robotic mower.
- Incompatible robotic mowers.
- Devices with damaged blade mounts, damaged threads, or defective fastening points.
- Use outside the intended application area.
- Use as a tool, hand knife, or for other cutting tasks outside the robotic mower.
Safety and Warning Notices
- Use only for the intended purpose.
- Use only with compatible robotic mowers, suitable blade discs, and appropriate mounting materials.
- Always turn off the robotic mower completely before any assembly, disassembly, cleaning, or maintenance.
- If possible, remove the battery or disconnect the device from the power supply.
- Always wait until the blade disc has come to a complete stop.
- Always wear appropriate protective gloves.
- Keep hands and feet away from rotating blades.
- Never touch knives, blades, or blade discs during operation.
- Do not use damaged, bent, heavily worn, rusted, or corroded knives, screws, or blade discs.
- Regularly check knives, screws, and blade discs for secure fit, wear, and damage.
- Use only suitable screws and appropriate mounting materials.
- If provided, use screws with locking lacquer or suitable screw locking.
- Keep children, animals, and uninvolved persons away from the work area.
- The robotic mower must not be operated if persons, especially children, or animals are in the work area.
- In case of unusual noises, vibrations, grinding noises, or running problems, stop operation immediately and check the assembly.
- In case of injuries or accidents, seek medical assistance immediately.
Assembly Instructions
Assembly may only be performed when the device is turned off. Always observe the operating instructions of the respective robotic mower.
Blade discs, replacement blades, and blades must be correctly seated and securely fastened. After assembly, check whether the blade disc runs freely and that no tools or foreign objects have been left in the area of the knives.
Check Before Operation
- Are all screws fully inserted and tightened?
- Is the blade disc correctly centered and securely fastened?
- Are the knives correctly mounted?
- Can movable knives move freely, if this is structurally intended?
- Are there no visible damages?
- Does the blade disc run freely and without grinding?
Maintenance and Inspection
- Regularly check knives, blades, screws, and blade discs for wear and damage.
- Immediately replace damaged or heavily worn parts.
- Regularly clean the blade disc of grass residues, dirt, and deposits.
- Do not use aggressive cleaning agents that may damage material or coating.
- Use only compatible replacement parts and suitable mounting materials.
Storage and Disposal
Store replacement blades, blades, screws, and blade discs dry, clean, and secure.
Keep out of reach of children and unauthorized persons.
Safely package used, damaged, or dull knives and blades to avoid cuts.
Dispose of metal parts, packaging, and accessories in accordance with local regulations.
Note on Original Accessories
CUT GUARD products are compatible accessories and replacement parts. They are not original accessories of the respective
device manufacturer unless explicitly stated in the product description. Brand names, model designations,
and manufacturer information are for compatibility indication only.
Contact for Safety Questions, Complaints, or Accidents
For questions regarding product safety, complaints, accidents, or indications of possible safety issues, please contact us immediately:
Patryk Napiorkowski - Trivando
Am bhf Weinhübel 8
02827 Görlitz
Germany
Email: service@trivando.de
Website: www.trivando.de
What are the differences between the 6-blade, 7-blade, and 9-blade cutting discs for my Sunseeker V3 or X3, and which one is best suited for my lawn?
The 9-blade cutting disc offers more cutting points, resulting in a finer and more even cut. For a well-maintained lawn or frequent mowing, the 9-blade variant is optimal, while the 6-blade or 7-blade models are more suitable for coarser cuts or less frequent mowing.
How can I tell that the 9-blade cutting disc of my Sunseeker V3 or X3 needs to be replaced?
A sign that a replacement is necessary is an uneven cut or if the robotic mower is making more noise than usual. Visible damage to the blades or increased wear of grass clippings are also warning signals.
How does using the 9-blade cutting disc affect the battery life and lawn health of my robotic mower?
The 9-blade cutting disc provides a uniform and precise cut, which improves lawn health. A clean cut minimizes stress on the grass plants, allowing the battery life of the robotic mower to be used optimally, as less energy is needed for reworking.
How long does shipping take for the 9-blade cutting disc for my Sunseeker V3 or X3, and can I return it if it doesn't fit?
Shipping usually takes place within 2-3 business days. If the blade disc does not fit your lawn mower or does not meet your expectations, you can return it within 30 days, provided it is unused and in its original packaging.
How do I change the 9-blade disc of my Sunseeker V3 or X3? What tools do I need and how long does it take?
Changing the 9-blade disc requires a wrench or a suitable screwdriver. First, remove the old disc, place the new one on, and tighten it. The entire assembly usually takes about 10-15 minutes.